Find Battery Exchangeable Gun-type Dental Curing Light, Dual LED Gun-type Curing Light, Dental Curing Light With Exchangeable Battery on Industry Directory, Reliable Manufacturer/Supplier/Factory from China.

Home > Products > Fuse & Holder > Gun-type Dental Curing Light

Gun-type Dental Curing Light

Gun-type Dental Curing Light

    Packaging: By paper box
    Productivity: 200 units / month
    Brand: Ultra-lite
    Transportation: Ocean,Air,Express
    Place of Origin: Taiwan
    Supply Ability: 200 units / month
    HS Code: 9018
    Port: Port of Keelung

Basic Info

Model No.: 1800E

Product Description

Product Description& Fields of Application

The Ultra-lite 1800E DUAL is a high-performance LED Curing Light intended for polymerization of light cured dental materials by dental professionals. The Ultra-lite 1000E DUAL Curing Light incorporates two types of LEDs to achieve broad wavelength with range of 390 to 480nm output to polymerize virtually all light-activated materials in the market and a high power mode to produce super-fast curing effect. The relevant range both for camphorquinone (CQ) and phenyl propanedione (PPD) containing product. Though the majority of light-curing dental materials are responsive in this range of wavelengths, it is suggested you should contact the filling material maker to make sure it before use.

Technical Data

Charging Base

AC Adapter Input: 100 – 240 VAC , 0.8 - 0.4 A , 47 – 63 Hz

OUTPUT: 12 VDC, 2.0 A

Charging box input: 12 VDC, 1 A

Fuse ration: 250V/2A

Charging box output: 8.4 VDC / 1.2A

Power indicator: Green LED

Charging indicator: Orange LED

Light intensity indicator: Blue LED

Dimensions (length/width/height): 150mm/90mm/60mm

Height with handpiece inserted: 180 mm

Weight: roughly 430 g

Handpiece

Power supply: Lithium battery – 7.4V DC, 2600 mAh

Wavelength range: 390 - 480 nm

Dimensions

Diameter: 50 mm

Length (with/without light guide): 185 / 125 mm

Height: 165 mm

Weight (with light guide and battery): Roughly 345 g

Charging Base and Handpiece

Time to charger empty battery: approximate 3 hrs

Relative humidity: max. 80% at 37max. 50% at 40

Protection from electric shock: Type BF (IEC601-1)

Equipment class: Class II (IEC601-1)

Protection from ingress of liquids: None

Protection from ingress of AP/APG: None

Applied Part: Light Probe

Operation

Activating and Deactivating the Curing Light

1. Activate the Curing Light by pressing the power button.

2. If it is desired to turn off the Curing Light, this can be done by again pressing the power button.

3. Curing: the probe tip shall be used in close proximity to the material to be cured. Avoid actual contact. The flat end of probe should be parallel to the surface being treated.

4. Curing Light intensity settings:

a. High mode: at constant intensity 1,900m W/cm2 - 2,000 mW/cm2

b. Soft start: initially 35 - 50% energy of high intensity and then Switch to high intensity

c. Low mode: at constant 35 - 50% energy of high intensity

d. Continuous mode: at a continuous on/off cycle of high intensity 2,000 mW/cm2

5. Curing time: High mode with different curing time: 1 sec to 5sec available

Low mode with 2 different curing time available: 5sec 10sec

Soft Start with 2 different curing time available: 7sec 12sec

Continuous mode with 16 cycles each of 1 sec, 2sec, 3sec; 1 second interval.

6. Total working time with new fully charged battery: approximate 30 minutes.

7. If the temperature on the handpiece is over 50, the overheat symbol will show up and the Buzzer will beeps 5 short tone. Curing Light will not be activated until device temperature lower than 50.

8. If the battery voltage gets too low, the battery capacity column will run out and the buzzer will beep 3 short tone. Please replace with another fully charged battery and place the empty battery into charging base for recharging.

9. Rotate the light guide into the optimal position for polymerization.

10 Place the light guide as close as possible to the filling material.

Avoid directly contacting the filling material!

a. Keep the light guide clean at all times to obtain optimal light output.

b. Damaged light guide must be replaced immediately, since damaged light guide may reduce light intensity or injures the patient.

11. When curing process is finished, always place the Curing Light back to holder.

Rolence Enterprise Inc.

  • 1
  • 2
  • 3
  • 4
 

Rolence Enterprise Inc. headquartered in Taiwan, develops, manufacturing & innovation on small equipment of Ultrasonic Scaler, Portable X-Ray, Dental Digital Sensor and LED Curing Light...etc. For over 40 years, we are an international supplier of dental equipment for various companies .


Multi-innovative developments & processes, proven know-how and high-quality have given us a leading position to our customer. and keep up with the innovative and creative design concepts into our products chain by incorporating the dentists` and other technology industry needs.


Besides, with further office locations will be in Germany, we will keep expending our office establish in different country afterward, and supporting our customer latest information, product training, and marking media to increase your business, that`s why we are approaching you to present ourselves & the products to reach a good cooperation in the future.

Company Info

  • Company Name: Rolence Enterprise Inc.
  • Representative: Sterling Cheng
  • Product/Service: Portable X-Ray , Curing Light , Ultrasonic Scaler , Curing Box , Dental Digital Sensor , UV Spot Curing
  • Capital (Million US $): TWD$65,400,000
  • Year Established: 1981
  • Total Annual Sales Volume (Million US $): US$2.5 Million - US$5 Million
  • Export Percentage: 81% - 90%
  • Total Annual Purchase Volume (Million US $): US$1 Million - US$2.5 Million
  • No. of Production Lines: 3
  • No. of R&D Staff: 5 -10 People
  • No. of QC Staff: Fewer than 5 People
  • OEM Services Provided: yes
  • Factory Size (Sq.meters): Below 1,000 square meters
  • Factory Location: No. 18-3 , Lane 231, Pu Chung Rd., Chungli Dist., Taoyuan City, Taiwan R.O.C. 32083
  • Contact Person: Mr. Peter Chiu
  • Tel: +886-3-4631999
Email to this supplier
  • *Subject:
  • To:

  • *Messages:
    Your message must be between 20-8000 characters